View IRLB3036GPBF_3501990.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

10/16/09 www.irf.com 1 hexfet power mosfet s d g IRLB3036GPBF gds gate drain source applications dc motor drive high efficiency synchronous rectification in smps uninterruptible power supply high speed power switching hard switched and high frequency circuits benefits optimized for logic level drive very low r ds(on) at 4.5v v gs superior r*q at 4.5v v gs improved gate, avalanche and dynamic dv/dt ruggedness fully characterized capacitance and avalanche soa enhanced body diode dv/dt and di/dt capability lead-free halogen-free to-220ab IRLB3036GPBF v dss 60v r ds ( on ) typ. 1.9m ? max. 2.4m ? i d ( silicon limited ) 270a i d (package limited) 195a absolute maximum ratings symbol parameter units i d @ t c = 25c continuous drain current, v gs @ 10v (silicon limited) i d @ t c = 100c continuous drain current, v gs @ 10v (silicon limited) i d @ t c = 25c continuous drain current, v gs @ 10v (package limited) i dm pulsed drain current p d @t c = 25c maximum power dissipation w linear derating factor w/c v gs gate-to-source voltage v dv/dt peak diode recovery v/ns t j operating junction and t stg storage temperature range soldering temperature, for 10 seconds (1.6mm from case) mounting torque, 6-32 or m3 screw avalanche characteristics e as (thermally limited) sin g le pulse avalanche ener g y mj i ar avalanche current a e ar repetitive avalanche ener g y mj thermal resistance symbol parameter typ. max. units r jc junction-to-case ??? 0.40 r cs case-to-sink, flat, greased surface 0.50 ??? r ja junction-to-ambient ??? 62 -55 to + 175 300 max. 270 190 1100 195 see fig. 14, 15, 22a, 22b a c c/w 290 380 8.0 16 2.5 10lb in (1.1n m) 96275

2 www.irf.com s d g pulse width 400s; duty cycle 2%. c oss eff. (tr) is a fixed capacitance that gives the same charging time as c oss while v ds is rising from 0 to 80% v dss . c oss eff. (er) is a fixed capacitance that gives the same energy as c oss while v ds is rising from 0 to 80% v dss .
calcuted continuous current based on maximum allowable junction temperature bond wire current limit is 195a. note that current limitation arising from heating of the device leds may occur with some lead mounting arrangements. repetitive rating; pulse width limited by max. junction temperature. limited by t jmax , starting t j = 25c, l = 0.021mh r g = 25 ? , i as = 165a, v gs =10v. part not recommended for use above this value . i sd 165a, di/dt 430a/s, v dd v (br)dss , t j 175c. static @ t j = 25c (unless otherwise specified) symbol parameter min. typ. max. unit s v (br)dss drain-to-source breakdown volta g e 60 ??? ??? v ? v (br)dss / ? t j breakdown volta g e temp. coefficient ??? 0.061 ??? v/c ??? 1.9 2.4 ??? 2.2 2.8 v gs(th) gate threshold volta g e 1.0 ??? 2.5 v i dss drain-to-source leaka g e current ??? ??? 20 ??? ??? 250 i gss gate-to-source forward leaka g e ??? ??? 100 gate-to-source reverse leaka g e ??? ??? -100 r g ( int ) internal gate resistance ??? 2.0 ??? ? dynamic @ t j = 25c (unless otherwise specified) symbol parameter min. typ. max. unit s g fs forward transconductance 340 ??? ??? s q g total gate char g e ??? 91 140 q gs gate-to-source char g e ??? 31 ??? q gd gate-to-drain ("miller") char g e ??? 51 ??? q sync total gate char g e sync. (q g - q gd ) ??? 40 ??? t d(on) turn-on delay time ??? 66 ??? t r rise time ??? 220 ??? t d(off) turn-off delay time ??? 110 ??? t f fall time ??? 110 ??? c iss input capacitance ??? 11210 ??? c oss output capacitance ??? 1020 ??? c rss reverse transfer capacitance ??? 500 ??? c oss eff. (er) effective output capacitance (energy related) ??? 1430 ??? c oss eff. (tr) effective output capacitance (time related) ??? 1880 ??? diode characteristics symbol parameter min. typ. max. unit s i s continuous source current ??? ??? (body diode) i sm pulsed source current ??? ??? (body diode) v sd diode forward volta g e ??? ??? 1.3 v t rr reverse recovery time ??? 62 ??? t j = 25c v r = 51v, ??? 66 ??? t j = 125c i f = 165a q rr reverse recovery char g e ??? 310 ??? t j = 25c di/d t = 100a/ s ??? 360 ??? t j = 125c i rrm reverse recovery current ??? 4.4 ??? a t j = 25c t on forward turn-on time intrinsic turn-on time is ne g li g ible (turn-on is dominated by ls+ld) v gs = 4.5v, i d = 140a m ? i d = 165a r g = 2.1 ? v gs = 4.5v v dd = 39v i d = 165a, v ds =0v, v gs = 4.5v conditions v ds = 10v, i d = 165a i d = 165a r ds(on) static drain-to-source on-resistance pf a 270 1100 nc a na nc ns v ds = v gs , i d = 250a v ds = 60v, v gs = 0v v ds = 60v, v gs = 0v, t j = 125c ns v gs = 0v, v ds = 0v to 48v mosfet symbol t j = 25c, i s = 165a, v gs = 0v integral reverse p-n junction diode. v gs = 16v conditions v gs = 0v, i d = 250a reference to 25c, i d = 5ma v gs = 10v, i d = 165a v gs = -16v showing the v ds = 30v conditions v gs = 4.5v v gs = 0v v ds = 50v ? = 1.0mhz v gs = 0v, v ds = 0v to 48v

www.irf.com 3 fig 1. typical output characteristics fig 3. typical transfer characteristics fig 4. normalized on-resistance vs. temperature fig 2. typical output characteristics fig 6. typical gate charge vs. gate-to-source voltage fig 5. typical capacitance vs. drain-to-source voltage 1 2 3 4 5 6 v gs , gate-to-source voltage (v) 0.1 1 10 100 1000 i d , d r a i n - t o - s o u r c e c u r r e n t ( a ) t j = 25c t j = 175c v ds = 25v 60s pulse width -60 -40 -20 0 20 40 60 80 100 120 140 160 180 t j , junction temperature (c) 0.5 1.0 1.5 2.0 2.5 r d s ( o n ) , d r a i n - t o - s o u r c e o n r e s i s t a n c e ( n o r m a l i z e d ) i d = 165a v gs = 10v 1 10 100 v ds , drain-to-source voltage (v) 100 1000 10000 100000 c , c a p a c i t a n c e ( p f ) v gs = 0v, f = 1 mhz c iss = c gs + c gd , c ds shorted c rss = c gd c oss = c ds + c gd c oss c rss c iss 0.1 1 10 100 1000 v ds , drain-to-source voltage (v) 0.1 1 10 100 1000 i d , d r a i n - t o - s o u r c e c u r r e n t ( a ) vgs top 15v 10v 4.5v 4.0v 3.5v 3.3v 3.0v bottom 2.7v 60s pulse width tj = 25c 2.7v 0.1 1 10 100 1000 v ds , drain-to-source voltage (v) 10 100 1000 i d , d r a i n - t o - s o u r c e c u r r e n t ( a ) 2.7v 60s pulse width tj = 175c vgs top 15v 10v 4.5v 4.0v 3.5v 3.3v 3.0v bottom 2.7v 0 20 40 60 80 100 120 q g , total gate charge (nc) 0.0 1.0 2.0 3.0 4.0 5.0 v g s , g a t e - t o - s o u r c e v o l t a g e ( v ) v ds = 48v v ds = 30v i d = 165a

4 www.irf.com fig 8. maximum safe operating area fig 10. drain-to-source breakdown voltage fig 7. typical source-drain diode forward voltage fig 11. typical c oss stored energy fig 9. maximum drain current vs. case temperature fig 12. maximum avalanche energy vs. draincurrent 0.0 0.5 1.0 1.5 2.0 2.5 v sd , source-to-drain voltage (v) 0.1 1 10 100 1000 i s d , r e v e r s e d r a i n c u r r e n t ( a ) t j = 25c t j = 175c v gs = 0v -60 -40 -20 0 20 40 60 80 100 120 140 160 180 t j , temperature ( c ) 55 60 65 70 75 v ( b r ) d s s , d r a i n - t o - s o u r c e b r e a k d o w n v o l t a g e ( v ) id = 5ma -10 0 10 20 30 40 50 60 70 v ds, drain-to-source voltage (v) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 e n e r g y ( j ) 25 50 75 100 125 150 175 starting t j , junction temperature (c) 0 200 400 600 800 1000 1200 e a s , s i n g l e p u l s e a v a l a n c h e e n e r g y ( m j ) i d top 27a 50a bottom 165a 25 50 75 100 125 150 175 t c , case temperature (c) 0 50 100 150 200 250 300 i d , d r a i n c u r r e n t ( a ) limited by package 0 1 10 100 v ds , drain-to-source voltage (v) 1 10 100 1000 10000 i d , d r a i n - t o - s o u r c e c u r r e n t ( a ) operation in this area limited by r ds (on) tc = 25c tj = 175c single pulse 100sec 1msec 10msec dc limited by package

www.irf.com 5 fig 13. maximum effective transient thermal impedance, junction-to-case fig 14. typical avalanche current vs.pulsewidth fig 15. maximum avalanche energy vs. temperature notes on repetitive avalanche curves , figures 14, 15: (for further info, see an-1005 at www.irf.com) 1. avalanche failures assumption: purely a thermal phenomenon and failure occurs at a temperature far in excess of t jmax . this is validated for every part type. 2. safe operation in avalanche is allowed as long ast jmax is not exceeded. 3. equation below based on circuit and waveforms shown in figures 22a, 22b. 4. p d (ave) = average power dissipation per single avalanche pulse. 5. bv = rated breakdown voltage (1.3 factor accounts for voltage increase during avalanche). 6. i av = allowable avalanche current. 7. ? t = allowable rise in junction temperature, not to exceed t jmax (assumed as 25c in figure 14, 15). t av = average time in avalanche. d = duty cycle in avalanche = t av f z thjc (d, t av ) = transient thermal resistance, see figures 13) p d (ave) = 1/2 ( 1.3bvi av ) = t/ z thjc i av = 2 t/ [1.3bvz th ] e as (ar) = p d (ave) t av 1e-006 1e-005 0.0001 0.001 0.01 0.1 t 1 , rectangular pulse duration (sec) 0.001 0.01 0.1 1 t h e r m a l r e s p o n s e ( z t h j c ) c / w 0.20 0.10 d = 0.50 0.02 0.01 0.05 single pulse ( thermal response ) notes: 1. duty factor d = t1/t2 2. peak tj = p dm x zthjc + tc j j 1 1 2 2 3 3 r 1 r 1 r 2 r 2 r 3 r 3 ci i / ri ci= i / ri c 4 4 r 4 r 4 ri (c/w) i (sec) 0.01115 0.000009 0.08360 0.000080 0.18950 0.001295 0.11519 0.006726 25 50 75 100 125 150 175 starting t j , junction temperature (c) 0 50 100 150 200 250 300 e a r , a v a l a n c h e e n e r g y ( m j ) top single pulse bottom 1.0% duty cycle i d = 165a 1.0e-06 1.0e-05 1.0e-04 1.0e-03 1.0e-02 1.0e-01 tav (sec) 1 10 100 1000 a v a l a n c h e c u r r e n t ( a ) 0.05 duty cycle = single pulse 0.10 allowed avalanche current vs avalanche pulsewidth, tav, assuming ? j = 25c and tstart = 150c. 0.01 allowed avalanche current vs avalanche pulsewidth, tav, assuming ? tj = 150c and tstart =25c (single pulse)

6 www.irf.com
fig 16. threshold voltage vs. temperature

-75 -50 -25 0 25 50 75 100 125 150 175 200 t j , temperature ( c ) 0.5 1.0 1.5 2.0 2.5 3.0 v g s ( t h ) , g a t e t h r e s h o l d v o l t a g e ( v ) i d = 250a i d = 1.0ma i d = 1.0a 0 100 200 300 400 500 di f /dt (a/s) 100 200 300 400 500 600 700 800 900 q r r ( a ) i f = 110a v r = 51v t j = 25c t j = 125c 0 100 200 300 400 500 di f /dt (a/s) 200 300 400 500 600 q r r ( a ) i f = 165a v r = 51v t j = 25c t j = 125c 0 100 200 300 400 500 di f /dt (a/s) 2 4 6 8 10 12 14 i r r m ( a ) i f = 110a v r = 51v t j = 25c t j = 125c 0 100 200 300 400 500 di f /dt (a/s) 2 4 6 8 10 12 i r r m ( a ) i f = 165a v r = 51v t j = 25c t j = 125c

www.irf.com 7 fig 23a. switching time test circuit fig 23b. switching time waveforms fig 22b. unclamped inductive waveforms fig 22a. unclamped inductive test circuit t p v (br)dss i as r g i as 0.01 ? t p d.u.t l v ds + - v dd driver a 15v 20v v gs fig 24a. gate charge test circuit fig 24b. gate charge waveform vds vgs id vgs(th) qgs1 qgs2 qgd qgodr fig 21.
for n-channel hexfet power mosfets

?

?
?

p.w. period di/dt diode recovery dv/dt ripple 5% body diode forward drop re-applied voltage reverse recovery current body diode forward current v gs =10v v dd i sd driver gate drive d.u.t. i sd waveform d.u.t. v ds waveform inductor curent d = p. w . period + - + + + - - - ? ?
!
"#"" ? $
%% ? "#""&#
d.u.t. v ds i d i g 3ma v gs .3 f 50k ? .2 f 12v current regulator same type as d.u.t. current sampling resistors + - v ds 90% 10% v gs t d(on) t r t d(off) t f '( 1 ) $
0.1 % ! + -

8 www.irf.com

to-220ab packages are not recommended for surface mount application. data and specifications subject to change without notice. this product has been designed and qualified for the industrial market. qualification standards can be found on ir?s web site. ir world headquarters: 233 kansas st., el segundo, california 90245, usa tel: (310) 252-7105 tac fax: (310) 252-7903 visit us at www.irf.com for sales contact information . 10/2009

! "#"$% & ' ( &(&)
* && *+
) & )(&) ,,+,& -,- +(& *(&) .//0!%.% "#1$% () *

▲Up To Search▲

Price & Availability of IRLB3036GPBF

	To Download IRLB3036GPBF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .